ГОСТ 27017-86

ГОСУДАРСТВЕННЫЙ СТАНДАРТ
СОЮЗА ССР

ИЗДЕЛИЯ КРЕПЕЖНЫЕ

ТЕРМИНЫ И ОПРЕДЕЛЕНИЯ

ГОСТ 27017-86

(СТ СЭВ 6300-88)

ГОСУДАРСТВЕННЫЙ КОМИТЕТ СССР ПО УПРАВЛЕНИЮ
КАЧЕСТВОМ ПРОДУКЦИИ И СТАНДАРТАМ

Москва

ГОСУДАРСТВЕННЫЙ СТАНДАРТ СОЮЗА ССР

ИЗДЕЛИЯ КРЕПЕЖНЫЕ

Термины и определения

Fasteners. Terms and definitions

ГОСТ
27017-86

(СТ СЭВ 6300-88)

Дата введения 01.01.88

Настоящий стандарт устанавливает термины и
определения основных понятий видов крепежных изделий общемашиностроительного
применения, их конструктивных элементов.

Термины, установленные настоящим стандартом, обязательны для применения во
всех видах документации и литературы, входящих в сферу действия стандартизации
или использующих результаты этой деятельности.

Настоящий стандарт должен применяться совместно с ГОСТ 11708.

Для каждого понятия установлен один стандартизованный термин. Применение
терминов — синонимов стандартизованного термина не допускается. Недопустимые к
применению термины-синонимы приведены в стандарте в качестве справочных и
обозначены пометой «Ндп».

Для отдельных стандартизованных терминов в стандарте приведены в качестве
справочных краткие формы, которые разрешается применять в случаях, исключающих
возможность их различного толкования.

Приведенные определения можно, при необходимости, изменять, вводя в них
производные признаки, раскрывая значение используемых в них терминов, указывая
объекты, входящие в объем определяемого понятия. Изменения не должны нарушать
объем и содержание понятий, определенных в данном стандарте.

В стандарте в качестве справочных приведены иноязычные эквиваленты для ряда
стандартизованных терминов на немецком (D), английском (E), французском (F) языках.

В стандарте приведены алфавитные указатели содержащихся в нем терминов на
русском языке и их иноязычных эквивалентов.

Стандартизованные термины набраны полужирным шрифтом, их краткая форма —
светлым, а недопустимые синонимы — курсивом.

В стандарте приведено приложение, содержащее терминологию и номенклатуру
крепежных изделий на русском, немецком, английском и французском языках.

(Измененная редакция, Изм. № 1).

Термин

Определение

 

ОБЩИЕ ПОНЯТИЯ

 

1. Крепежное изделие

Деталь для
образования соединения

E. Fastener

2. Болт

Крепежное изделие
в форме стержня с наружной резьбой на одном конце, с головкой на другом,
образующее соединение при помощи гайки или резьбового отверстия в одном из
соединяемых изделий

D. Schraube

E. Bolt

F. Boulon

3. Винт

Крепежное изделие
для образования соединения или фиксации, выполненное в форме стержня с
наружной резьбой на одном конце и конструктивным элементом для передачи
крутящего момента на другом.

D. Schraube

Е. Screw

F. Vis

Примечание. Конструктивный элемент винта для передачи
крутящего момента может представлять головку со шлицем, головку с накаткой
или, при отсутствии головки, шлиц в торце стержня

4. Шуруп

Крепежное изделие
в форме стержня с наружной специальной резьбой, резьбовым коническим концом и
головкой на другом конце, образующее резьбу в отверстии соединяемого
деревянного или пластмассового изделия.

D. Holzschraube

Е. Wood screw

Примечание. Специальная резьба имеет треугольный
заостренный профиль и большую ширину впадины по сравнению с шириной зуба

F. Vis à
bois

5. Шпилька

Крепежное изделие
в форме цилиндрического стержня с наружной резьбой на обоих концах или на
всей длине стержня

D.
Stiftschraube

Е. Stud

F. Goujon

6. Штифт

Крепежное изделие
в форме цилиндрического или конического стержня для фиксации изделий при
сборке

D. Stift

Е. Pin

F. Goupille

7. Гайка

Крепежное изделие
с резьбовым отверстием конструктивным элементом для передачи крутящего
момента.

D. Mutter

Е.
Nut

Примечание. Конструктивным элементом гайки для
передачи крутящего момента может быть многогранник, накатка на боковой
поверхности, торцевые и радиальные отверстия, шлицы и т.д.

F. Ecrou

8. Шайба

Крепежное изделие
с отверстием, подкладываемое под гайку или головку болта или винта для
увеличения опорной поверхности и (или) предотвращения их самоотвинчивания

D. Scheibe

E. Washer

F. Rondelle

9. Шплинт

Крепежное изделие
в форме проволочного стержня полукруглого сечения, сложенного вдвое с
образованием головки

D. Splint

Е. Split pin

F. Goupille

10. Заклепка

Крепежное изделие
в форме гладкого цилиндрического стержня с головкой на одном конце, служащее
для получения неразъемного соединения за счет образования головки на другом
конце стержня пластической деформацией

D. Niet

Е. Rivet

F. Rivet

ВИДЫ КРЕПЕЖНЫХ ИЗДЕЛИЙ

11. Ступенчатый болт

Болт, диаметр
гладкой части стержня которого превышает номинальный диаметр резьбы

D. Schraube
rnit Ansatzschaft

Е. Shoulder
bolt

F. Corps de
boulon renforcée

12. Откидной болт

Болт, головка
которого выполнена в виде подвижной части шарнирного соединения

D.
Augenschraube

Е. Eye bolt

F. Corps de
boulon à oeil

13. Призонный болт

Болт, диаметр
гладкой части стержня которого определяют из условия обеспечения работы
соединения на срез

Ндп. Болт для
отверстий из-под развертки

D.
Paßschraube

Е. Fit bolt

F. Corps de
boulon ajustable

14. Фундаментный болт

Болт, со
специальной формой головки, служащий для крепления оборудования к фундаменту.

D.
Steinschraube

Е. Foundation
holt

Примечание. Специальная форма головки может
представлять раздвинутые лапки прорезной части стержня, отогнутую часть
стержня и т.д.

F. Tige de
scellement

15. Невыпадающий винт

Винт, диаметр
гладкой части стержня которого меньше внутреннего диаметра резьбы

D. Schraube mit
Dehnschaft

Е. Screw with
waisted shank

F. Vis à
tige allégée

16. Самонарезающий винт

Винт, образующий
специальную резьбу в отверстии одного из соединяемых пластмассовых или
металлических изделий

D.
Blechschraube

Е. Self-tapping
screw

F. Vis à
tôle

17. Самосверлящий самонарезающий винт

Самонарезающий
винт с концом формы сверла

18. Установочный винт

Винт с концом
специальной формы, служащий для фиксации изделий относительно друг друга

Е. Set screw

Примечание. Специальная форма конца может быть
цилиндрической, конической, плоской и т.д.

19. Пружинный штифт

Цилиндрический
штифт трубчатого сечения с продольным пазом по его длине, свернутой из
пружинной стали

20. Прорезная гайка

Шестигранная гайка
с радиально расположенными прорезями под шплинт со стороны одной из торцевых
поверхностей

D. Kronenmutter

E. Hexagon
slotted nut

F. Ecrou
hexagonal à créneaux

21. Корончатая гайка

Шестигранная
гайка, часть которой выполнена в виде цилиндра с радиально расположенными
прорезями под шплинт

D. Kronenmutter

Е. Hexagon
castle nut

F. Ecrou
hexagonal à créneaux dégagés

22. Колпачковая гайка

Гайка, со
сферической и плоской торцевой поверхностями и глухим резьбовым отверстием

D. Hutmutter

Е. Acorn nut

F. Ecrou borgne
à calotte

23. Гайка-барашек

Гайка с плоскими
выступающими элементами для передачи крутящего момента

D.
Flügelmutter

Е. Wing nut

F. Ecrou
à oreilles

24. Плоская шайба

Шайба с плоской
опорной поверхностью

D. Scheibe

Е. Plain washer

F. Rondelle
plate

25. Пружинная шайба

Разрезная круглая
шайба, концы которой расположены в разных плоскостях, служащая для
предотвращения самоотвинчивания крепежных изделий при ее упругой деформации
под нагрузкой

Ндп. Шайба
Гровера

D. Federring

E. Spring
washer

F. Rondelle
élastique

26. Стопорная шайба

Шайба, служащая
для предотвращения самоотвинчивания крепежных изделий при помощи
конструктивных элементов.

D. Scheibe mit
Lappen oder Nasen

Е. Tab washer

Примечание. Конструктивными элементами шайбы являются
лапки, носки, зубья и т.д.

F. Frein
d’écrou

27. Пустотелая заклепка

Заклепка со
стержнем трубчатого сечения

28. Полупустотелая заклепка

Заклепка, концевая
часть стержня которой имеет трубчатое сечение

ЭЛЕМЕНТЫ КРЕПЕЖНЫХ ИЗДЕЛИЙ

29. Стержень крепежного изделия

Часть крепежного
изделия, непосредственно входящая в отверстия соединяемых изделий или
ввертываемая в материал одного из них

Стержень

30. Головка крепежного изделия

Часть крепежного
изделия, имеющего стержень, служащая для передачи крутящего момента и (или)
образования опорной поверхности

Головка

D. Kopf

E. Head

F. Tête

31. Подголовок болта

Гладкая часть
стержня болта цилиндрической, овальной или квадратной формы, непосредственно
примыкающая к головке и служащая для центрирования болта или предотвращения
его проворачивания

Подголовок

D. Ansatz

E. Neck

F. Collet

32. Бурт крепежного изделия

Выступ на опорной
поверхности многогранной гайки, головки болта или винта, выполненный в форме
цилиндра или усеченного конуса диаметром, бóльшим диаметра их
описанной окружности

Бурт

Ндп. Фланец

D. Bund

E. Collar

F. Embase

33. Опорный выступ крепежного изделия

Кольцевой выступ
на опорной поверхности многогранной гайки или головки болта, диаметр которого
меньше размера под ключ.

Опорный выступ

Примечание. Под размером под ключ понимается
расстояние между противоположными гранями многогранной гайки или головки
болта, винта, измеренное в плоскости, нормальной к их оси

Ндп. Опорная
шайба

«Мертвая шайба»

D. Telleransatz

E. Washer face

F. Collerette

34. Шлиц крепежного изделия

Углубление
специальной формы в торце головки болта, винта или шурупа, в торце
установочного винта без головки, вдоль образующей или в торце гайки

Шлиц

Примечание. Форма шлица может быть шестигранной,
крестообразной, в виде сквозной или несквозной прорези и т.д.

35. Шип болта

Выступ на опорной
поверхности головки болта, служащий для предотвращения его проворачивания

Шип

36. Ус болта

Выступ на опорной
поверхности головки и стержня болта, служащий для предотвращения его
проворачивания

Ус

D. Nase

E. Nib

F. Ergot

37. Буравчик

Резьбовой
конической конец шурупа, служащий для нарезания резьбы в деревянном или
пластмассовом изделии при образовании соединения

E. Gimlet point

Содержание
  1. АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА РУССКОМ ЯЗЫКЕ
  2. АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА НЕМЕЦКОМ ЯЗЫКЕ
  3. АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА АНГЛИЙСКОМ ЯЗЫКЕ
  4. АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ФРАНЦУЗСКОМ ЯЗЫКЕ
  5. ПРИЛОЖЕНИЕ
  6. ТЕРМИНОЛОГИЯ И НОМЕНКЛАТУРА КРЕПЕЖНЫХ ИЗДЕЛИЙ НА РУССКОМ, НЕМЕЦКОМ, АНГЛИЙСКОМ И ФРАНЦУЗСКОМ ЯЗЫКАХ
  7. I. ТЕРМИНОЛОГИЯ И НОМЕНКЛАТУРА КРЕПЕЖНЫХ ИЗДЕЛИЙ
  8. 1. РЕЗЬБА
  9. 2. ФОРМЫ ГОЛОВОК
  10. 3. ФОРМЫ СТЕРЖНЕЙ
  11. 4. КОНЦЫ БОЛТОВ И ВИНТОВ
  12. 5. ЭЛЕМЕНТЫ, ПЕРЕДАЮЩИЕ ВРАЩЕНИЕ
  13. 6. БОЛТЫ И ВИНТЫ С ШЕСТИГРАННОЙ ГОЛОВКОЙ
  14. 7. ВИНТЫ С ЧЕТЫРЕХГРАННОЙ (КВАДРАТНОЙ) ГОЛОВКОЙ
  15. 8. БОЛТЫ С ТРЕХГРАННОЙ ГОЛОВКОЙ
  16. 9. БОЛТЫ С ВОСЬМИГРАННОЙ ГОЛОВКОЙ
  17. 10. БОЛТЫ С ДВЕНАДЦАТИГРАННОЙ ГОЛОВКОЙ
  18. 11. БОЛТЫ С Т-ОБРАЗНОЙ ГОЛОВКОЙ
  19. 12. БОЛТЫ С ПОЛУКРУГЛОЙ ГОЛОВКОЙ
  20. 13. БОЛТЫ С ПОТАЙНЫМИ ГОЛОВКАМИ
  21. 14. ВИНТЫ С ВНУТРЕННИМ ШЕСТИГРАННИКОМ
  22. 15. ВИНТЫ С ПРЯМЫМ ШЛИЦЕМ
  23. 16. ВИНТЫ С КРЕСТООБРАЗНЫМ ШЛИЦЕМ
  24. 17. ВИНТЫ С НЕВЫПАДАЮЩИМИ ДЕТАЛЯМИ
  25. 18. РАЗЛИЧНЫЕ ТИПЫ БОЛТОВ И ВИНТОВ
  26. 19. УСТАНОВОЧНЫЕ ВИНТЫ БЕЗ ГОЛОВОК
  27. 20. САМОНАРЕЗАЮЩИЕ ВИНТЫ
  28. 21. ШУРУПЫ
  29. 22. РЕЗЬБОНАРЕЗАЮЩИЕ ВИНТЫ
  30. 23. РЕЗЬБОВЫДАВЛИВАЮЩИЕ ВИНТЫ
  31. 24. ВИНТЫ С РИФЛЕНОЙ ГОЛОВКОЙ
  32. 25. ШТИФТЫ
  33. 26. ШПИЛЬКИ
  34. 27. ЗАКЛЕПКИ
  35. 28. ГАЙКИ
  36. 29. ШАЙБЫ
  37. 30. ШПЛИНТЫ
  38. II. АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА РУССКОМ ЯЗЫКЕ
  39. III. УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА НЕМЕЦКОМ ЯЗЫКЕ
  40. IV. УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА АНГЛИЙСКОМ ЯЗЫКЕ
  41. V. УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА ФРАНЦУЗСКОМ ЯЗЫКЕ

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА РУССКОМ ЯЗЫКЕ

Болт                                                                                                                               2

Болт для отверстий из-под развертки                                                                   13

Болт откидной                                                                                                           12

Болт призонный                                                                                                       13

Болт ступенчатый                                                                                                    11

Болт фундаментный                                                                                                14

Буравчик                                                                                                                    37

Бурт                                                                                                                              32

Бурт крепежного изделия                                                                                       32

Винт                                                                                                                               3

Винт невыпадающий                                                                                              15

Винт самонарезающий                                                                                            16

Винт самонарезающий самосверлящий                                                              17

Винт установочный                                                                                                 18

Выступ крепежного изделия опорный                                                                33

Выступ опорный                                                                                                         33

Гайка                                                                                                                            7

Гайка-барашек                                                                                                         23

Гайка колпачковая                                                                                                 22

Гайка корончатая                                                                                                    21

Гайка прорезная                                                                                                       20

Головка                                                                                                                        30

Головка крепежного изделия                                                                                30

Заклепка                                                                                                                    10

Заклепка полупустотелая                                                                                      28

Заклепка пустотелая                                                                                               27

Изделие крепежное                                                                                                   1

Подголовок                                                                                                                  31

Подголовок болта                                                                                                     31

Стержень                                                                                                                     29

Стержень крепежного изделия                                                                             29

Ус                                                                                                                                 36

Ус болта                                                                                                                      36

Фланец                                                                                                                         32

Шайба                                                                                                                           8

Шайба Гровера                                                                                                           25

Шайба «мертвая»                                                                                                      33

Шайба опорная                                                                                                           33

Шайба плоская                                                                                                         24

Шайба пружинная                                                                                                   25

Шайба стопорная                                                                                                      26

Шип                                                                                                                             35

Шип болта                                                                                                                  35

Шлиц                                                                                                                           34

Шлиц крепежного изделия                                                                                    34

Шпилька                                                                                                                      5

Шплинт                                                                                                                        9

Штифт                                                                                                                           6

Штифт пружинный                                                                                                  19

Шуруп                                                                                                                           4

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА НЕМЕЦКОМ ЯЗЫКЕ

Ansatz                                                                                                                           31

Augenschraube                                                                                                              12

Blechschraube                                                                                                               16

Bund                                                                                                                              32

Federring                                                                                                                      25

Flügelmulter                                                                                                                  23

Holzschraube                                                                                                                  4

Hutmutter                                                                                                                      22

Kopf                                                                                                                              30

Kronenmutte                                                                                                            20, 21

Mutter                                                                                                                             7

Nase                                                                                                                              36

Niet                                                                                                                               10

Paßschraube                                                                                                                  13

Scheibe                                                                                                                     8, 24

Scheibe mit Lappen oder Nasen                                                                                    26

Schraube                                                                                                                     2, 3

Schraube mit Ansatzschaft                                                                                            11

Schraube mit Dehnschaft                                                                                               15

Splint                                                                                                                              9

Steinschraube                                                                                                                14

Stift                                                                                                                                 6

Stiftschraube                                                                                                                   5

Telleransatz                                                                                                                  33

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА АНГЛИЙСКОМ ЯЗЫКЕ

Acorn nut                                                                                                                      22

Bolt                                                                                                                                 2

Collar                                                                                                                            32

Eye bolt                                                                                                                         12

Fastener                                                                                                                          1

Fit bolt                                                                                                                          13

Foundation bolt                                                                                                             14

Gimlet point                                                                                                                  37

Head                                                                                                                             30

Hexagon castle nut                                                                                                        21

Hexagon slotted nut                                                                                                       20

Neck                                                                                                                              31

Nib                                                                                                                                36

Nut                                                                                                                                  7

Pin                                                                                                                                   6

Plain washer                                                                                                                 24

Rivet                                                                                                                             10

Screw                                                                                                                              3

Screw with waisted shank                                                                                            15

Self-tapping screw                                                                                                        16

Set screw                                                                                                                      18

Shoulder bolt                                                                                                                11

Split pin                                                                                                                          9

Spring washer                                                                                                               25

Stud                                                                                                                                 5

Tab washer                                                                                                                   26

Washer                                                                                                                            8

Washer face                                                                                                                  33

Wing nut                                                                                                                        23

Wood screw                                                                                                                    4

АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ФРАНЦУЗСКОМ ЯЗЫКЕ

Boulon                                                                                                                            2

Collerette                                                                                                                      33

Collet                                                                                                                            31

Corps de boulon ajustable                                                                                            13

Corps de boulon à oeil                                                                                                  12

Corps de boulon renforcée                                                                                            11

Ecrou                                                                                                                              7

Ecrou à oreilles                                                                                                            23

Ecrou borgne á calotte                                                                                                  22

Ecrou hexagonal à créneaux                                                                                          20

Ecrou hexagonal à créneaux
dégagés                                                                            21

Embase                                                                                                                         32

Ergot                                                                                                                             36

Frein d’écrou                                                                                                                26

Goujon                                                                                                                            5

Goupille                                                                                                                      6, 9

Rivet                                                                                                                             10

Rondelle                                                                                                                         8

Rondelle élastique                                                                                                        25

Rondelle plate                                                                                                               24

Tête                                                                                                                               30

Tige de scellement                                                                                                        14

Vis                                                                                                                                  3

Vis à bois                                                                                                                        4

Vis à tige allégée                                                                                                          15

Vis à tôle                                                                                                                       16

ПРИЛОЖЕНИЕ

Справочное

ТЕРМИНОЛОГИЯ И НОМЕНКЛАТУРА КРЕПЕЖНЫХ ИЗДЕЛИЙ НА РУССКОМ,
НЕМЕЦКОМ, АНГЛИЙСКОМ И ФРАНЦУЗСКОМ ЯЗЫКАХ

I. ТЕРМИНОЛОГИЯ И НОМЕНКЛАТУРА КРЕПЕЖНЫХ ИЗДЕЛИЙ

1. РЕЗЬБА

Наименование

Чертеж

1.1. Резьба

1.2. Коническая резьба

1.3. Самонарезающая резьба

1.4. Шурупная резьба

1.5. Метрическая резьба

1.6. Метрическая резьба с мелким шагом

2. ФОРМЫ ГОЛОВОК

Наименование

Чертеж

2.1. Шестигранная головка

2.2. Шестигранная головка с опорным выступом

2.3. Шестигранная головка с цилиндрическим буртом

2.4. Шестигранная головка с фланцем

2.5. Квадратная головка

2.6. Квадратная головка с цилиндрическим буртом

2.7. Трехгранная головка с цилиндрическим буртом

2.8. Восьмигранная головка

2.9. Двенадцатигранная головка с фланцем

2.10. Т-образная головка

2.11. Т-образная головка с квадратным подголовком

2.12. Полукруглая головка

2.13. Низкая полукруглая головка

2.14. Полукруглая головка с усом

2.15. Низкая полукруглая головка с квадратным подголовком

2.16. Полукруглая головка с овальным подголовком

2.17. Цилиндрическая головка

2.18. Цилиндрическая головка со сферой

2.19. Низкая цилиндрическая головка со сферой

2.20. Цилиндрическая скругленная головка

2.21. Потайная головка

2.22. Потайная головка с заплечиком

2.23. Потайная головка с усом

2.24. Потайная головка с квадратным подголовком

2.25. Полупотайная головка

2.26. Полупотайная головка с заплечиком

2.27. Рифленая цилиндрическая головка с прямым рифлением

2.28. Рифленая цилиндрическая головка с сетчатым рифлением

3. ФОРМЫ СТЕРЖНЕЙ

Наименование

Чертеж

3.1. Нормальный стержень (стержень, диаметр которого равен номинальному
диаметру резьбы)

3.2. Уменьшенный стержень (стержень, диаметр которого приблизительно
равен среднему диаметру резьбы)

3.3. Увеличенный стержень, диаметр которого больше номинального диаметра
резьбы

3.4. Утоненный
стержень (стержень, диаметр которого меньше внутреннего диаметра резьбы)

3.5. Ступенчатый
стержень

3.6. Пустотелый
стержень

3.7. Полупустотелый
стержень

4. КОНЦЫ БОЛТОВ И ВИНТОВ

Наименование

Чертеж

4.1. Конец без
фаски

4.2. Сферический конец

4.3. Конец с фаской

4.4. Конический конец

4.5. Конический притупленный конец

4.6. Засверленный конец

4.7. Плоский конец

4.8. Цилиндрический конец

4.9. Цилиндрический укороченный конец

4.10. Ступенчатый конец со сферой

4.11. Ступенчатый конец с конусом

4.12. Конический с притуплением конец самонарезающего винта с режущей
кромкой

4.13. Конический конец самонарезающего винта

4.14. Плоский конец самонарезающего винта

4.15. Конец резьбовыдавливающего винта

4.16. Буравчик шурупа

5. ЭЛЕМЕНТЫ, ПЕРЕДАЮЩИЕ ВРАЩЕНИЕ

Наименование

Чертеж

5.1. Шестигранник

5.2. Квадрат

5.3. Трехгранник

5.4. Восьмигранник

5.5. Двенадцатигранник

5.6. Трехгранное углубление

5.7. Квадратное углубление

5.8. Шестигранное углубление

5.9. Шлицевое углубление

5.10. Зубчатое углубление

5.11. Прямой шлиц

5.12. Крестообразный шлиц

5.13. Барашек

5.14. Прямое рифление

5.15. Сетчатое рифление

5.16. Накрест расположенные отверстия

6. БОЛТЫ И ВИНТЫ С ШЕСТИГРАННОЙ ГОЛОВКОЙ

Наименование

Чертеж

6.1. Болт с шестигранной головкой

6.2. Ступенчатый болт с шестигранной головкой

6.3. Установочный винт с шестигранной головкой и цилиндрическим концом

6.4. Установочный винт с шестигранной головкой и ступенчатым концом с
конусом

6.5. Винт с шестигранной головкой и утоненным стержнем

6.6. Болт с шестигранной головкой с цилиндрическим буртом

6.7. Болт с шестигранной головкой с фланцем

7. ВИНТЫ С ЧЕТЫРЕХГРАННОЙ (КВАДРАТНОЙ) ГОЛОВКОЙ

Наименование

Чертеж

7.1. Винт с квадратной головкой

7.2. Винт с квадратной головкой с цилиндрическим буртом

7.3. Установочный винт с квадратной головкой и цилиндрическим концом

7.4. Установочный винт с квадратной головкой и засверленным концом

7.5. Установочный винт с квадратной головкой с цилиндрическим буртом и
ступенчатым концом со сферой

8. БОЛТЫ С ТРЕХГРАННОЙ ГОЛОВКОЙ

Наименование

Чертеж

8. Болт с трехгранной головкой с цилиндрическим буртом

9. БОЛТЫ С ВОСЬМИГРАННОЙ ГОЛОВКОЙ

Наименование

Чертеж

9. Болт с восьмигранной головкой

10. БОЛТЫ С ДВЕНАДЦАТИГРАННОЙ ГОЛОВКОЙ

Наименование

Чертеж

10. Болт с
двенадцатигранной головкой с фланцем

11. БОЛТЫ С Т-ОБРАЗНОЙ ГОЛОВКОЙ

Наименование

Чертеж

11.1. Болт с Т-образной головкой

11.2. Болт с Т-образной головкой и квадратным подголовком

11.3. Болт с Т-образной головкой и выступами под головкой

12. БОЛТЫ С ПОЛУКРУГЛОЙ ГОЛОВКОЙ

Наименование

Чертеж

12.1. Болты с низкой полукруглой головкой и квадратным подголовком

12.2. Болт с полукруглой головкой и усом

12.3. Болт с низкой полукруглой головкой и усом

12.4. Болт с полукруглой головкой и овальным подголовком

13. БОЛТЫ С ПОТАЙНЫМИ ГОЛОВКАМИ

Наименование

Чертеж

13.1. Болт с потайной головкой и квадратным подголовком

13.2. Болт с потайной головкой и усом

13.3. Шинный болт

14. ВИНТЫ С ВНУТРЕННИМ ШЕСТИГРАННИКОМ

Наименование

Чертеж

14.1. Винт с цилиндрической головкой и шестигранным углублением под ключ

14.2. Ступенчатый винт с цилиндрической головкой и шестигранным
углублением под ключ

14.3. Винт с потайной головкой и шестигранным углублением под ключ

15. ВИНТЫ С ПРЯМЫМ ШЛИЦЕМ

Наименование

Чертеж

15.1. Винт с цилиндрической головкой

15.2. Винт с цилиндрической скругленной головкой

15.3. Винт с цилиндрической головкой со сферой

15.4. Установочный винт с цилиндрической головкой со сферой и
цилиндрическим концом

15.5. Ступенчатый винт с цилиндрической головкой со сферой

15.6. Винт с цилиндрической головкой со сферой, с отверстием в головке

15.7. Винт с уменьшенной цилиндрической головкой со сферой

15.8. Винт с потайной головкой

15.9. Установочный винт с потайной головкой и цилиндрическим концом

15.10. Винт с полупотайной головкой

15.11. Установочный винт с полупотайной головкой и цилиндрическим концом

15.12. Винт с потайной головкой и прямым закрытым шлицем

15.13. Винт с полукруглой головкой

16. ВИНТЫ С КРЕСТООБРАЗНЫМ ШЛИЦЕМ

Наименование

Чертеж

16.1. Винт с цилиндрической головкой со сферой и крестообразным шлицем

16.2. Винт с потайной головкой и крестообразным шлицем

16.3. Винт с полупотайной головкой и крестообразным шлицем

16.4. Винт с полукруглой головкой и крестообразным шлицем

17. ВИНТЫ С НЕВЫПАДАЮЩИМИ ДЕТАЛЯМИ

Наименование

Чертеж

17.1. Винт с шестигранной головкой с невыпадающей плоской шайбой

17.2. Винт с шестигранной головкой с невыпадающими пружинной и плоской
шайбами

17.3. Винт с цилиндрической головкой со сферой и невыпадающей пружинной
шайбой

17.4. Винт с полупотайной головкой и невыпадающей стопорной шайбой

18. РАЗЛИЧНЫЕ ТИПЫ БОЛТОВ И ВИНТОВ

Наименование

Чертеж

18.1. Откидной болт

18.2. Болт с низкой полукруглой головкой и шипом

18.3. Болт с плоской головкой и шипом

18.4. Болт с потайной головкой и двумя шипами

18.5. Костыльковый болт

18.6. Болт с колпачковой головкой

18.7. Конический болт

18.8. Анкерный болт

18.9. Фундаментный болт

18.10. Винт-барашек

18.11. Рым-болт

19. УСТАНОВОЧНЫЕ ВИНТЫ БЕЗ ГОЛОВОК

Наименование

Чертеж

19.1. Установочный винт с плоским концом

19.2. Установочный винт с цилиндрическим концом

19.3. Установочный винт с засверленным концом

19.4. Установочный винт с коническим концом

19.5. Установочный винт с плоским концом и шестигранным углублением под
ключ

19.6. Установочный винт с цилиндрическим концом и шестигранным
углублением под ключ

19.7. Установочный винт с засверленным концом и шестигранным углублением
под ключ

19.8. Установочный винт с коническим концом и шестигранным углублением
под ключ

20. САМОНАРЕЗАЮЩИЕ ВИНТЫ

Наименование

Чертеж

20.1. Самонарезающий винт с шестигранной головкой

20.2. Самонарезающий винт с цилиндрической головкой

20.3. Самонарезающий винт с потайной головкой

20.4. Самонарезающий винт с полупотайной головкой

20.5. Самонарезающий винт с потайной головкой и крестообразным шлицем

20.6. Самонарезающий винт с полупотайной головкой и крестообразным шлицем

20.7. Самонарезающий винт с цилиндрической скругленной головкой и
крестообразным шлицем

21. ШУРУПЫ

Наименование

Чертеж

21.1. Шуруп с шестигранной головкой

21.2. Шуруп с квадратной головкой

21.3. Шуруп с полукруглой головкой

21.4. Шуруп с полупотайной головкой

21.5. Шуруп с потайной головкой

21.6. Шуруп с полукруглой головкой и крестообразным шлицем

21.7. Шуруп с полупотайной головкой и крестообразным шлицем

21.8. Шуруп с потайной головкой и крестообразным шлицем

22. РЕЗЬБОНАРЕЗАЮЩИЕ ВИНТЫ

Наименование

Чертеж

22.1. Резьбонарезающий винт с шестигранной головкой

22.2. Резьбонарезающий винт с цилиндрической головкой

22.3. Резьбонарезающий винт с потайной головкой

22.4. Резьбонарезающий винт с полупотайной головкой

22.5. Резьбонарезающий винт с цилиндрической головкой со сферой и
крестообразным шлицем

22.6. Резьбонарезающий винт с потайной головкой и крестообразным шлицем

22.7. Резьбонарезающий винт с полупотайной головкой и крестообразным
шлицем

23. РЕЗЬБОВЫДАВЛИВАЮЩИЕ ВИНТЫ

Наименование

Чертеж

23. Резьбовыдавливающий винт

24. ВИНТЫ С РИФЛЕНОЙ ГОЛОВКОЙ

Наименование

Чертеж

24.1. Винт с рифленой цилиндрической головкой и плоским концом

24.2. Винт с рифленой цилиндрической головкой и коническим концом

24.3. Винт с рифленой цилиндрической головкой и ступенчатым концом с
конусом

24.4. Винт с рифленой цилиндрической головкой и засверленным концом

24.5. Винт с рифленой цилиндрической головкой и сферическим концом

24.6. Винт с рифленой цилиндрической головкой и цилиндрическим концом

25. ШТИФТЫ

Наименование

Чертеж

25.1. Цилиндрический штифт

25.2. Цилиндрический штифт с внутренней резьбой

25.3. Цилиндрический штифт с засверленными концами

25.4. Цилиндрический насеченный штифт

25.5. Цилиндрический насеченный штифт с коническими насечками

25.6. Конический разводной штифт

25.7. Конический штифт

25.8. Конический штифт с внутренней резьбой

25.9. Конический
штифт с резьбовой цапфой

25.10. Пружинный
штифт

25.11. Резьбовой
штифт с плоским концом и шлицем

25.12. Резьбовой
штифт с плоским концом и шестигранным углублением под ключ

25.13. Резьбовой
штифт с коническим притупленным концом и шестигранным углублением под ключ

25.14. Резьбовой
штифт с цилиндрическим концом и шестигранным углублением под ключ.

25.15. Резьбовой
штифт с засверленным концом и шестигранным углублением под ключ

26. ШПИЛЬКИ

Наименование

Чертеж

26.1. Шпилька

26.2. Шпилька с утоненным стержнем

26.3. Шпилька с резьбой по всей длине

26.4. Приварная шпилька

26.5. Стяжная шпилька с проточками и шестигранным хвостовиком

27. ЗАКЛЕПКИ

Наименование

Чертеж

27.1. Заклепка с полукруглой головкой

27.2. Заклепка с полукруглой низкой головкой

27.3. Заклепка с потайной головкой

27.4. Заклепка с полупотайной головкой

27.5. Заклепка с полупотайной низкой головкой

27.6. Заклепка с плоской головкой

27.7. Пустотелая заклепка со скругленной головкой

27.8. Пустотелая заклепка с плоской головкой

27.9. Пустотелая заклепка с потайной головкой

27.10. Пустотелая заклепка с плоской головкой

27.11. Пустотелая заклепка с потайной головкой

27.12. Полупустотелая заклепка с полукруглой головкой

28. ГАЙКИ

Наименование

Чертеж

28.1. Шестигранная гайка

28.2. Шестигранная низкая гайка

28.3. Шестигранная гайка с цилиндрическим буртом

28.4. Шестигранная гайка с фланцем

28.5. Шестигранная гайка с опорной шайбой

28.6. Шестигранная приварная гайка

28.7. Квадратная гайка

28.8. Квадратная низкая гайка

28.9. Анкерная гайка

28.10. Квадратная гайка с цилиндрическим буртом

28.11. Квадратная приварная гайка

28.12. Трехгранная гайка с цилиндрическим буртом

28.13. Восьмигранная гайка

28.14. Двенадцатигранная гайка с фланцем

28.15. Самоконтрящаяся гайка с деформированной резьбой

28.16. Самоконтрящаяся гайка с кольцевой вставкой из полимера

28.17. Шестигранная прорезная гайка

28.18. Шестигранная корончатая гайка

28.19. Шестигранная низкая корончатая гайка

28.20. Колпачковая гайка

28.21. Рифленая гайка

28.22. Круглая гайка со шлицем на торце

28.23. Шлицевая гайка

28.24. Круглая гайка с радиально расположенными отверстиями

28.25. Круглая гайка с отверстиями на торце под ключ

28.26. Гайка-барашек

29. ШАЙБЫ

Наименование

Чертеж

29.1. Круглая плоская шайба

29.2. Квадратная шайба

29.3. Круглая шайба с квадратным отверстием

29.4. Косая шайба

29.5. Пружинная шайба

29.6. Пружинная шайба с отогнутыми концами

29.7. Пружинная двухвитковая шайба

29.8. Пружинная изогнутая шайба

29.9. Стопорная шайба с наружными зубьями

29.10. Стопорная шайба с внутренними зубьями

29.11. Стопорная шайба с зубьями под винты с потайной и полупотайной
головкой

29.12. Пружинная волнистая шайба

29.13. Пружинная шайба с наружными зубьями

29.14. Пружинная шайба с внутренними зубьями

29.15. Пружинная шайба с зубьями под винты с потайной и полупотайной
головкой

29.16. Стопорная шайба с двумя лапками

29.17. Стопорная шайба с наружным носком

29.18. Стопорная шайба с лапкой

29.19. Стопорная шайба с внутренним носком

30. ШПЛИНТЫ

Наименование

Чертеж

30. Шплинт

II.
АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА РУССКОМ ЯЗЫКЕ

Барашек                                                                                                                          5.13

Болт анкерный                                                                                                              18.8

Болт конический                                                                                                           18.7

Болт костыльковый                                                                                                       18.5

Болт откидной                                                                                                               18.1

Болт с восьмигранной головкой                                                                                  9

Болт с двенадцатигранной головкой с фланцем                                                       10

Болт с колпачковой головкой                                                                                      18.6

Болт с низкой полукруглой головкой и
квадратным подголовком                         12.1

Болт с низкой полукруглой головкой и усом                                                             12.3

Болт с низкой полукруглой головкой и шипом                                                         18.2

Болт с плоской головкой и шипом                                                                              18.3

Болт с полукруглой головкой и овальным
подголовком                                          12.4

Болт с полукруглой головкой и усом                                                                          12.2

Болт с потайной головкой и квадратным
подголовком                                           13.1

Болт с потайной головкой и двумя шипами                                                              18.4

Болт с потайной головкой и усом                                                                               13.2

Болт с Т-образной головкой                                                                                        11.1

Болт с Т-образной головкой и выступами под
головкой                                          11.3

Болт с Т-образной головкой и квадратным
подголовком                                        11.2

Болт с трехгранной головкой с цилиндрическим
буртом                                        8

Болт ступенчатый с шестигранной головкой                                                            6.2

Болт с шестигранной головкой                                                                                   6.1

Болт с шестигранной головкой с фланцем                                                                6.7

Болт с шестигранной головкой с цилиндрическим
буртом                                     6.6

Болт фундаментный                                                                                                     18.9

Болт шинный                                                                                                                 13.3

Буравчик шурупа                                                                                                           4.16

Винт-барашек                                                                                                                                             18.10

Винт резьбовыдавливающий                                                                                       23

Винт резьбовыдавливающий с полупотайной
головкой                                          22.4

Винт резьбонарезающий с полупотайной головкой
и крестообразным шлицем  22.7

Винт резьбонарезающий с потайной головкой                                                         22.3

Винт резьбонарезающий с потайной головкой и
крестообразным шлицем          22.6

Винт резьбонарезающий с цилиндрической головкой                                             22.2

Винт резьбонарезающий с цилиндрической
головкой со сферой и крестообразным
шлицем                                                                                                                                  22.5

Винт резьбонарезающий с шестигранной головкой                                                 22.1

Винт самонарезающий с полупотайной головкой                                                    20.4

Винт самонарезающий с полупотайной головкой и
крестообразным шлицем     20.6

Винт самонарезающий с потайной головкой                                                            20.3

Винт самонарезающий с потайной головкой и крестообразным
шлицем             20.5

Винт самонарезающий с цилиндрической головкой                                                20.2

Винт самонарезающий с цилиндрической
скругленной головкой и крестообразным
шлицем                                                                                                                                 20.7

Винт самонарезающий с шестигранной головкой                                                    20.1

Винт с квадратной головкой                                                                                       7.1

Винт с квадратной головкой с цилиндрическим буртом                                         7.2

Винт с полукруглой головкой                                                                                                                                             15.13

Винт с полукруглой головкой и крестообразным шлицем                                      16.4

Винт с полупотайной головкой                                                                                                                                             15.10

Винт с полупотайной головкой и крестообразным шлицем                                    16.3

Винт с полупотайной головкой и невыпадающей стопорной
шайбой                   17.4

Винт с потайной головкой                                                                                           15.8

Винт с потайной головкой и крестообразным шлицем                                            16.2

Винт с потайной головкой и прямым закрытым шлицем                                                                                                                                             15.12

Винт с потайной головкой и шестигранным углублением под
ключ                     14.3

Винт с рифленой цилиндрической головкой и засверленным
концом                  24.4

Винт с рифленой цилиндрической головкой и коническим
концом                     24.2

Винт с рифленой цилиндрической головкой и плоским концом                           24.1

Винт с рифленой цилиндрической головкой и ступенчатым
концом и конусом 24.3

Винт с рифленой цилиндрической головкой и сферическим
концом                   24.5

Винт с рифленой цилиндрической головкой и цилиндрическим
концом             24.6

Винт ступенчатый с цилиндрической головкой со сферой                                     15.5

Винт ступенчатый с цилиндрической головкой и
шестигранным углублением под
ключ                                                                                                                               14.2

Винт с уменьшенной цилиндрической головкой со сферой                                    15.7

Винт с цилиндрической головкой                                                                              15.1

Винт с цилиндрической головкой со сферой                                                            15.3

Винт с цилиндрической головкой со сферой и крестообразным
шлицем             16.1

Винт с цилиндрической головкой со сферой и невыпадающей пружинной шайбой                                                                                                                                17.3

Винт с цилиндрической головкой со сферой, с отверстием в
головке                   15.6

Винт с цилиндрической головкой и шестигранным углублением
под ключ         14.1

Винт с цилиндрической скругленной головкой                                                        15.2

Винт с шестигранной головкой с невыпадающей плоской
шайбой                        17.1

Винт с шестигранной головкой с невыпадающими
пружинной и плоской шайбами                                                                                                                                 17.2

Винт с шестигранной головкой и утоненным стержнем                                         6.5

Винт установочный с засверленным концом                                                            19.3

Винт установочный с засверленным концом и
шестигранным углублением под
ключ                                                                                                                                 19.7

Винт установочный с квадратной головкой и засверленным
концом                    7.4

Винт установочный с квадратной головкой и
цилиндрическим буртом и
ступенчатым концом со сферой                                                                                                                                  7.5

Винт установочный с квадратной головкой и цилиндрическим
концом               7.3

Винт установочный с коническим концом                                                                19.4

Винт установочный с коническим концом и
шестигранным углублением под
ключ                                                                                                                               19.8

Винт установочный с плоским концом                                                                      19.1

Винт установочный с плоским концом и
шестигранным углублением под
ключ                                                                                                                              19.5

Винт установочный с полупотайной головкой и
цилиндрическим концом                                                                                                                                             15.11

Винт установочный с потайной головкой и цилиндрическим
концом                  15.9

Винт установочный с цилиндрическим концом                                                       19.2

Винт установочный с цилиндрическим концом и
шестигранным углублением под
ключ                                                                                                                                  19.6

Винт установочный с цилиндрической головкой
со сферой и цилиндрическим
концом                                                                                                                                     15.4

Винт установочный с шестигранной головкой и
ступенчатым концом с конусом                                                                                                                                 6.4

Винт установочный с шестигранной головкой и
цилиндрическим концом          6.3

Восьмигранник                                                                                                             5.4

Гайка анкерная                                                                                                             28.9

Гайка-барашек                                                                                                                                             28.26

Гайка восьмигранная                                                                                                                                             28.13

Гайка двенадцатигранная с фланцем                                                                                                                                             28.14

Гайка квадратная                                                                                                          28.7

Гайка квадратная низкая                                                                                             28.8

Гайка квадратная приварная                                                                                                                                             28.11

Гайка квадратная с цилиндрическим буртом                                                                                                                                             28.10

Гайка колпачковая                                                                                                                                             28.20

Гайка круглая с отверстиями на торце под ключ                                                                                                                                             28.25

Гайка круглая с радиально расположенными отверстиями                                                                                                                                             28.24

Гайка круглая со шлицем на торце                                                                                                                                             28.22

Гайка рифленая                                                                                                                                             28.21

Гайка самоконтрящаяся с деформированной резьбой                                                                                                                                             28.15

Гайка самоконтрящаяся с кольцевой вставкой из полимера                                                                                                                                             28.16

Гайка трехгранная с цилиндрическим буртом                                                                                                                                             28.12

Гайка шестигранная                                                                                                     28.1

Гайка шестигранная корончатая                                                                                                                                             28.18

Гайка шестигранная низкая                                                                                         28.2

Гайка шестигранная низкая корончатая                                                                                                                                             28.19

Гайка шестигранная приварная                                                                                  28.6

Гайка шестигранная прорезная                                                                                                                                             28.17

Гайка шестигранная с опорной шайбой                                                                     28.5

Гайка шестигранная с фланцем                                                                                  28.4

Гайка шестигранная с цилиндрическим буртом                                                       28.3

Гайка шлицевая                                                                                                                                             28.23

Головка восьмигранная                                                                                                2.8

Головка двенадцатигранная с фланцем                                                                     2.9

Головка квадратная                                                                                                      2.5

Головка квадратная с цилиндрическим буртом                                                        2.6

Головка низкая полукруглая                                                                                        2.13

Головка низкая полукруглая с квадратным подголовком                                        2.15

Головка низкая цилиндрическая со сферой                                                              2.19

Головка полукруглая                                                                                                    2.12

Головка полукруглая с овальным подголовком                                                        2.16

Головка полукруглая с усом                                                                                        2.14

Головка полупотайная                                                                                                 2.25

Головка полупотайная с заплечиком                                                                         2.26

Головка потайная                                                                                                         2.21

Головка потайная с заплечиком                                                                                 2.22

Головка потайная с квадратным подголовком                                                          2.24

Головка потайная с усом                                                                                             2.23

Головка рифленая цилиндрическая с прямым рифлением                                      2.27

Головка рифленая цилиндрическая с сетчатым рифлением                                   2.28

Головка цилиндрическая со сферой                                                                           2.18

Головка Т-образная                                                                                                      2.10

Головка Т-образная с квадратным подголовком                                                       2.11

Головка трехгранная с цилиндрическим буртом                                                      2.7

Головка цилиндрическая                                                                                             2.17

Головка цилиндрическая скругленная                                                                       2.20

Головка шестигранная                                                                                                 2.1

Головка шестигранная с фланцем                                                                              2.4

Головка шестигранная с опорной шайбой                                                                 2.2

Головка шестигранная с цилиндрическим буртом                                                   2.3

Двенадцатигранник                                                                                                      5.5

Заклепка полупустотелая с плоской головкой                                                                                                                                             27.10

Заклепка полупустотелая с полукруглой головкой                                                                                                                                             27.12

Заклепка полупустотелая с потайной головкой                                                                                                                                             27.11

Заклепка с плоской головкой                                                                                      27.6

Заклепка с полукруглой
головкой                                                                               27.1

Заклепка с полукруглой низкой головкой                                                                 27.2

Заклепка с полупотайной головкой                                                                            27.4

Заклепка с полупотайной низкой головкой                                                               27.5

Заклепка с потайной головкой                                                                                    27.3

Заклепка пустотелая с плоской головкой                                                                  27.8

Заклепка пустотелая с потайной головкой                                                                27.9

Заклепка пустотелая со скругленной головкой                                                         27.7

Квадрат                                                                                                                          5.2

Конец без фаски                                                                                                            4.1

Конец засверленный                                                                                                     4.6

Конец конический                                                                                                        4.4

Конец конический притупленный                                                                              4.5

Конец плоский                                                                                                              4.7

Конец резьбовыдавливающего винта                                                                         4.15

Конец самонарезающего винта конический                                                              4.13

Конец самонарезающего винта конический с притуплением с режущей кромкой                                                                                                                               4.12

Конец самонарезающего винта плоский                                                                    4.14

Конец ступенчатый с конусом                                                                                    4.11

Конец ступенчатый со сферой                                                                                    4.10

Конец с фаской                                                                                                             4.3

Конец сферический                                                                                                      4.2

Конец цилиндрический                                                                                               4.8

Конец цилиндрический укороченный                                                                        4.9

Отверстия, накрест расположенные                                                                           5.16

Резьба                                                                                                                             1.1

Резьба коническая                                                                                                        1.2

Резьба метрическая                                                                                                      1.5

Резьба метрическая с мелким шагом                                                                          1.6

Резьба самонарезающая                                                                                               1.3

Резьба шурупная                                                                                                            1.4

Рифление прямое                                                                                                          5.14

Рифление сетчатое                                                                                                       5.15

Рым-болт                                                                                                                                             18.11

Стержень нормальный                                                                                                 3.1

Стержень полупустотелый                                                                                          3.7

Стержень пустотелый                                                                                                  3.6

Стержень ступенчатый                                                                                                3.5

Стержень увеличенный                                                                                                3.3

Стержень уменьшенный                                                                                              3.2

Стержень утоненный                                                                                                    3.4

Трехгранник                                                                                                                  5.3

Углубление квадратное                                                                                                5.7

Углубление трехгранное                                                                                              5.8

Углубление шестигранное                                                                                           5.9

Шайба квадратная                                                                                                        29.2

Шайба косая                                                                                                                  29.4

Шайба круглая с квадратным отверстием                                                                 29.3

Шайба круглая плоская                                                                                                29.1

Шайба пружинная                                                                                                        29.5

Шайба пружинная волнистая                                                                                                                                             29.12

Шайба пружинная двухвитковая                                                                                 29.7

Шайба пружинная изогнутая                                                                                       29.8

Шайба пружинная с отогнутыми концами                                                                29.6

Шайба пружинная с внутренними зубьями                                                                                                                                             29.14

Шайба пружинная с зубьями под винты с потайной и
полупотайной головкой                                                                                                                                             29.15

Шайба пружинная с наружными зубьями                                                                                                                                             29.13

Шайба стопорная с внутренними зубьями                                                                                                                                             29.10

Шайба стопорная с внутренним носком                                                                                                                                             29.19

Шайба стопорная с двумя лапками                                                                                                                                             29.16

Шайба стопорная с зубьями под винты с
потайной и полупотайной головками                                                                                                                                    29.11

Шайба стопорная с лапкой                                                                                                                                             29.18

Шайба стопорная с наружными зубьями                                                                   19.9

Шайба стопорная с наружным носком                                                                                                                                             29.17

Шестигранник                                                                                                               5.1

Шлиц крестообразный                                                                                                 5.12

Шлиц прямой                                                                                                                5.11

Шпилька                                                                                                                        26.1

Шпилька приварная                                                                                                     26.4

Шпилька с резьбой по всей длине                                                                              26.3

Шпилька стяжная с проточками и шестигранным хвостовиком                            26.5

Шпилька с утоненным стержнем                                                                               26.2

Шплинт                                                                                                                          30

Штифт конический                                                                                                      25.7

Штифт конический разводной                                                                                    25.6

Штифт конический с внутренней резьбой                                                                25.8

Штифт конический с резьбовой цапфой                                                                   25.9

Штифт пружинный                                                                                                                                             25.10

Штифт резьбовой с засверленным концом и
шестигранным углублением под
ключ                                                                                                                                    25.15

Штифт резьбовой с коническим притупленным
концом и шестигранным
углублением под ключ                                                                                                                               25.13

Штифт резьбовой с плоским концом и шестигранным
углублением под ключ                                                                                                                                             25.12

Штифт резьбовой с плоским концом и шлицем                                                                                                                                             25.11

Штифт резьбовой с цилиндрическим концом и
шестигранным углублением под
ключ                                                                                                                               25.14

Штифт цилиндрический                                                                                              25.1

Штифт цилиндрический насеченный                                                                        25.4

Штифт цилиндрический насеченный с коническими насечками                          25.5

Штифт цилиндрический с внутренней резьбой                                                        25.2

Штифт цилиндрический с засверленными концами                                                25.3

Шуруп с квадратной головкой                                                                                    21.2

Шуруп с полукруглой головкой                                                                                  21.3

Шуруп с полукруглой головкой и крестообразным шлицем                                   21.6

Шуруп с полупотайной головкой                                                                                21.4

Шуруп с полупотайной головкой и крестообразным шлицем                                 21.7

Шуруп с потайной головкой                                                                                        21.5

Шуруп с потайной головкой и крестообразным шлицем                                         21.8

Шуруп с шестигранной головкой                                                                                21.1

III.
УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА НЕМЕЦКОМ ЯЗЫКЕ

Gewinde                                                                                                                          1.1.

Kegliges
(konisches) Gewinde                                                                                        1.2.

Blechschraubengewinde                                                                                                  1.3.

Holzschraubengewinde                                                                                                    1.4.

metrisches
Gewinde                                                                                                        1.5.

metrisches
Feingewinde                                                                                                  1.6.

Sechskantkopf                                                                                                                  2.1.

Sechskantkopf
mit Telleransalz                                                                                       2.2.

Sechskantkopf
mit Bund                                                                                                   2.3.

Sechskantkopf
mit Flansch (Flanschkopf)                                                                        2.4.

Vierkantkopf                                                                                                                    2.5.

Vierkantkopf
mit Bund                                                                                                     2.6.

Dreikantkopf
mit Bund                                                                                                     2.7.

Achtkantkopf                                                                                                                    2.8.

Zwölfkantkopf
mit Flansch                                                                                              2.9.

Hammerkopf                                                                                                                    2.10.

Hammerkopf
mit Vierkantansatz                                                                                      2.11.

Halbrundkopf                                                                                                                   2.12.

Flachrundkopf                                                                                                                  2.13.

Halbrundkopf
mit Nase                                                                                                    2.14.

Flachrundkopf
mit Vierkantansatz                                                                                    2.15.

Halbrundkopf
mit Ovalansatz                                                                                          2.16.

Zylinderkopf                                                                                                                    2.17.

Linsenzylinderkopf                                                                                                          2.18.

Linsenkopf                                                                                                                       2.19.

Flachkopf                                                                                                                         2.20.

Senkkopf                                                                                                                          2.21.

abgesetzter
mit Senkkopf                                                                                                 2.22.

Senkkopf
mit Nase                                                                                                           2.23.

Sekkopf
mit Vierkantansatz                                                                                              2.24.

Linsensenkkopf                                                                                                                2.25.

abgesetzter
Linsensenkkopf                                                                                             2.26.

Rändelkopf                                                                                                                      2.27.

Kordelkopf                                                                                                                      2.28.

Dickschaft
(Schaftdurchmesser = Gewindedurchmesser)                                                3.1.

Dünnschaft
(Schaftdurchmesser »
Flankendurchmesser)                                                 3.2.

Paßschaft
(Schaftdurchmesser > Gewindedurchmesser)                                                 3.3.

Dehnschaft
(Schaftdurchmesser < Kerndurchmesser)                                                      3.4.

Ansatzschaft                                                                                                                     3.5.

Hohlschaft                                                                                                                       3.6.

Halbhohlschaft                                                                                                                 3.7.

ohne
Kuppe                                                                                                                      4.1.

Linsenkuppe                                                                                                                     4.2.

Kegelkuppe                                                                                                                      4.3.

Spitze                                                                                                                               4.4.

Spitze,
abgeflacht                                                                                                            4.5.

Ringschneide                                                                                                                   4.6.

Kegelstumpf                                                                                                                     4.7.

Zapfen                                                                                                                              4.8.

Kernansatz                                                                                                                       4.9.

Ansatzkuppe                                                                                                                    4.10.

Ansatzspitze,
abgeflacht                                                                                                  4.11.

Schneidschraubenende
mit Schabenut                                                                              4.12.

Blechschrauben
— Spitze                                                                                                  4.13.

Blechschrauben
— Zapfen                                                                                                 4.14.

Gewindeformendes
Schraubenende                                                                                 4.15.

Spitze
(Nagelbohrer)                                                                                                       4.16.

Sechskant                                                                                                                         5.1.

Vierkant                                                                                                                           5.2.

Dreikant                                                                                                                           5.3.

Achtkant                                                                                                                           5.4.

Zwölfkant                                                                                                                        5.5.

Innendreikant                                                                                                                   5.6.

Innenvierkant                                                                                                                   5.7.

Innensechskant                                                                                                                 5.8.

Innenkeilprofil                                                                                                                 5.9.

Innenzwölfzahn                                                                                                                5.10.

gerader
Schlitz                                                                                                                 5.11.

Kreuzschlitz                                                                                                                     5.12.

Flügel                                                                                                                              5.13.

Rändel                                                                                                                             5.14.

Kordel                                                                                                                             5.15.

Kreuzloch                                                                                                                        5.16.

Sechskantschraube                                                                                                           6.1.

Sechskant
— Paßschraube                                                                                                 6.2.

Sechskantschraube
mit Zapfen                                                                                         6.3.

Sechskantschrauhe
mit Ansatzspitze                                                                                6.4.

Sechskantschraube
mit Dehnschaft                                                                                  6.5.

Sechskantschraube
mit Bund                                                                                            6.6.

Sechskantschraube
mit Flansch                                                                                        6.7.

Vierkantschraube                                                                                                             7.1.

Vierkantschrauhe
mit Bund                                                                                              7.2.

Vierkantschraube
mit Zapfen                                                                                           7.3.

Vierkantschraube
mit Ringschneide                                                                                 7.4.

Vierkantschraube
mit Bund und Ansatzkuppe                                                                  7.5.

Dreikantschraube                                                                                                             8.

Achtkantschraube                                                                                                             9.

Zwölfkantschraube
mit Flansch                                                                                       10.

Hammerschraube                                                                                                             11.1.

Hammerschraube
mit Vierkantansatz                                                                               11.2.

Hammerschraube
mit Nase                                                                                              11.3.

Flachrundschraube
mit Vierkantansatz                                                                             12.1.

Halbrundschraube
mit Nase                                                                                             12.2.

Flachrundschraube
mit Nase                                                                                            12.3.

Halbrundschraube
mit Ovalansatz                                                                                   12.4.

Senkschraube
mit Vierkantansatz                                                                                     13.1.

Senkschraube
mit Nase                                                                                                    13.2.

Kegelsenkschraube                                                                                                          13.3.

Zylinderschraube
mit Innensechskant                                                                               14.1.

Zylinderschraube
mit Innensechskant und Ansatzschaft                                                   14.2.

Senkschrauben
mit Innensechskant                                                                                   14.3.

Zylinderschraube
mit Schlitz                                                                                           15.1.

Flachkopfschraube
mit Schlitz                                                                                         15.2.

Linsenzylinderschraube
mit Schlitz                                                                                 15.3.

Linsenzylinderschraube
mit Schlitz und Zapfen                                                               15.4.

Linsenzylinderschraube
mit Schlitz und Ansatz                                                               15.5.

Linsenzylinderschraube
mit Schlitz und Kreuzloch                                                          15.6.

Linsenzylinderschraube
mit Schlitz und kleinem Kopf                                                    15.7.

Senkschraube
mit Schlitz                                                                                                 15.8.

Senkschraube
mit Schlitz und Zapfen                                                                               15.9.

Linsensenkschraube
mit Schlitz                                                                                                                                             15.10.

Linsensenkschraube
mit Schlitz und Zapfen                                                                                                                                             15.11.

Senkschraube
mit Halteschlitz                                                                                                                                             15.12.

Halbrundschraube
mit Schlitz                                                                                                                                             15.13.

Linsenschraube
mit Kreuzschlitz und Dehnschaft                                                            16.1.

Senkschraube
mil Kreuzschlitz                                                                                        16.2.

Linsensenkschraube
mit Kreuzschlitz                                                                              16.3.

Flachkopfschraube
mit Kreuzschlitz                                                                                16.4.

Sechskantschraube
mit unverlierbarer Scheibe                                                               17.1.

Sechskantschraube
mit unverlierbarem Federring und Scheibe                                       17.2.

Linsenzylinderschraube
mit unverlierbarem Federring                                                    17.3.

Linsensenkschraube
mit unverlierbarer Fächerscheibe                                                   17.4.

Augenschraube                                                                                                                18.1.

Bogenklammerschraube                                                                                                   18.2.

Flachklammerschraube                                                                                                    18.3.

Tellerschraube
mit Nasen                                                                                                18.4.

Hakenschraube                                                                                                                18.5.

Hutschraube                                                                                                                     18.6.

Kegelschraube                                                                                                                 18.7.

Steinschraube                                                                                                                  18.8.

Steinschraube                                                                                                                  18.9.

Flügelschraube                                                                                                                                             18.10.

Ringschraube                                                                                                                                             18.11.

Gewindestift
mit Schlitz und Kegelstumpf                                                                       19.1.

Gewindestift
mit Schlitz und Zapfen                                                                                19.2.

Gewindestift
mit Schlitz und Ringschneide                                                                     19.3.

Gewindestift
mit Schlitz und Spitze                                                                                 19.4.

Gewindestift
mit Innensechskant und Kegelstumpf                                                          19.5.

Gewindestift
mit Innensechskant und Zapfen                                                                   19.6.

Gewindestift
mit Innensechskant und Ringschneide                                                         19.7.

Gewindestifl
mil Innensechskant und Spitze                                                                    19.8.

Sechskantblechschraube                                                                                                  20.1.

Zylinderblechschraube
mit Schlitz                                                                                   20.2.

Senkblechschraube
mit Schlitz                                                                                        20.3.

Linsensenkblechschraube
mit Schlitz                                                                               20.4.

Senkblechschraube
mit Kreuzschlitz                                                                                20.5.

Linsensenkblechschraube
mit Kreuzschlitz                                                                      20.6.

Flachkopf-Blechschraube
mit Kreuzschlitz                                                                     20.7.

Sechskantholzschraube                                                                                                    21.1.

Vierkantholzschraube                                                                                                      21.2.

Halbrundholzschraube
mit Schlitz                                                                                   21.3.

Linsensenkbolzschraube
mit Schlitz                                                                                21.4.

Senkholzschraube
mit Schlitz                                                                                          21.5.

Halbrundholzschraube
mit Kreuzschlitz                                                                          21.6.

Linsensenkholzschraube
mit Kreuzschlitz                                                                        21.7.

Senkholzschraube
mit Kreuzschlitz                                                                                  21.8.

Sechskant-Schneidschraube                                                                                             22.1.

Zylinder-Schneidschraube
mit Schlitz                                                                             22.2.

Senk-Schneidschraube
mit Schlitz                                                                                   22.3.

Linsensenk-Schneidschraube
mit Schlitz                                                                         22.4.

Linsenzylinder-Schneidschraube
mit Kreuzschlitz                                                           22.5.

Senk-Schneidschraube
mit Kreuzschlitz                                                                          22.6.

Linsensenk-Schneidschraube
mit Kreuzschlitz                                                                22.7.

Sechskantschraube,
gewindefurchend                                                                              23.

Rändelschraube                                                                                                               24.1.

Rändelschraube
mit Spitze                                                                                              24.2.

Rändelschraube
mit Ansatzspitze                                                                                    24.3.

Rändelschraube
mit Ringschneide                                                                                   24.4.

Rändelschraube
mit Linsenkuppe                                                                                    24.5.

Rändelschraube
mit Zapfen                                                                                             24.6.

Zylinderstift                                                                                                                     25.1.

Zylinderstift
mit Innengewinde                                                                                        25.2.

Nietstift                                                                                                                            25.3.

Zylinderkerbstift                                                                                                              25.4.

Kegelkerbstift                                                                                                                  25.5.

Kegelstift
mit Spreizende                                                                                                25.6.

Kegelstift                                                                                                                         25.7.

Kegelstift
mit Innengewinde                                                                                            25.8.

Kegelstift
mit Gewindezapfen                                                                                         25.9.

Spannstift                                                                                                                                             25.10.

Gewindestift
mit Schlitz, Schaft und Kegelstumpf                                                                                                                                             25.11.

Gewindestift
mit Innensechskant, Schaft und Kegelstumpf                                                                                                                                             25.12.

Gewindestift
mit Innensechskant, Schaft und Spitze                                                                                                                                             25.13.

Gewindestift
mit Innensechskant, Schaft und Zapfen                                                                                                                                             25.14.

Gewindestift
mit Innensechskant, Schaft und Ringschneide                                                                                                                                             25.15.

Stiftschraube                                                                                                                    26.1.

Stiftschraube
mit Dehnschaft                                                                                           26.2.

Gewindebolzen                                                                                                                26.3.

Anschweißende                                                                                                               26.4.

Schraubenbolzen
ohne Dehnschaft und Zapfen                                                                26.5.

Halbrundniet                                                                                                                    27.1.

Flachrundniet                                                                                                                   27.2.

Senkniet                                                                                                                           27.3.

Linsenniet                                                                                                                        27.4.

flacher
Linsenniet                                                                                                            27.5.

Flachkopfniet                                                                                                                   27.6.

Hohlniet
mit Linsenkopf                                                                                                  27.7.

Hohlniet
mit Flachkopf                                                                                                    27.8.

Hohlniet
mit Senkkopf                                                                                                     27.9.

Halb-Hohlniet
mit Flachkopf                                                                                                                                             27.10.

Halb-Hohlniet
mit Senkkopf                                                                                                                                             27.11.

Halb-Hohlniet
mit Halbrundkopf                                                                                                                                             27.12.

Sechskantmutter                                                                                                               28.1.

Flache
Sechskantmutter                                                                                                   28.2.

Sechskantmutter
mit Bund                                                                                                28.3.

Sechskantmutter
mit Flansch                                                                                            28.4.

Sechskantmutter
mil Ansatz                                                                                             28.5.

Sechskant-Anschweißmutter                                                                                            28.6.

Vierkantmutter                                                                                                                 28.7.

Flache
Vierkantmutter                                                                                                      28.8.

Ankermutter                                                                                                                     28.9.

Vierkantmutter
mit Bund                                                                                                                                             28.10.

Vierkant-Anschweißmutter                                                                                                                                             28.11.

Dreikantmutter
mit Bund                                                                                                                                             28.12.

Achtkantmutter                                                                                                                                             28.13.

Zwölfkantmutter
mit Flansch                                                                                                                                             28.14.

Sechskantmutter
mit Klemmteil, ganzmetallisch                                                                                                                                             28.15.

Sechskantmutter
mit Klemmteil, mit nichtmetallischem Einsatz                                                                                                                                             28.16.

Kronenmutter                                                                                                                                             28.17.

Kronenmutter                                                                                                                                             28.18.

Flache
Kronenmutter                                                                                                                                             28.19.

Hutmutter                                                                                                                                             28.20.

Rändelmutter                                                                                                                                             28.21.

Schlitzmutter                                                                                                                                             28.22.

Nutmutter                                                                                                                                             28.23.

Kreuzlochmutter                                                                                                                                             28.24.

Zweilochmulter                                                                                                                                             28.25.

Flügelmutter                                                                                                                                             28.26.

Scheibe                                                                                                                            29.1.

Vierkantscheibe                                                                                                               29.2.

Scheibe
mit Vierkantloch                                                                                                 29.3.

Keilscheibe                                                                                                                     29.4.

Federring                                                                                                                         29.5.

Federring,
aufgebogen                                                                                                     29.6.

Mehrfachfederring                                                                                                           29.7.

Federscheibe,
gewölbt                                                                                                    29.8.

Fächerscheibe,
außen gezahnt                                                                                          29.9.

Fächerscheibe,
innen gezahnt                                                                                                                                             29.10.

Fächerscheibe,
außen gezahnt, keglig                                                                                                                                             29.11.

Federscheibe,
gewellt                                                                                                                                             29.12.

Zahnscheibe,
innen gezahnt                                                                                                                                             29.13.

Zahnscheibe,
außen gezahnt                                                                                                                                             29.14.

Zahnscheibe,
außen gezahnt, keglig                                                                                                                                             29.15.

Sicherungsblech
mit zwei Lappen                                                                                                                                             29.16.

Sicherungsblech
mit Nase, außen                                                                                                                                             29.17.

Sicherungsblech
mit Lappen                                                                                                                                             29.18.

Sicherungsblech
mit Nase, innen                                                                                                                                             29.19.

Splint                                                                                                                               30.

IV. УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА АНГЛИЙСКОМ ЯЗЫКЕ

Screw
thread                                                                                                                   1.1.

Taper
screw thread                                                                                                          1.2.

Tapping
screw thread                                                                                                      1.3.

Wood
screw thread                                                                                                         1.4.

Metric
thread (SI)                                                                                                            1.5.

Metric
fine pitch thread                                                                                                   1.6.

Hexagon
head                                                                                                                  2.1.

Hexagon
head with washer face                                                                                      2.2.

Hexagon
head with collar                                                                                                2.3.

Hexagon
head with flange                                                                                                2.4.

Square
head                                                                                                                     2.5.

Square
head with collar                                                                                                   2.6.

Triangle
head with collar                                                                                                2.7.

Octagonal
head                                                                                                                2.8.

12point
flange head                                                                                                         2.9.

T-head                                                                                                                             2.10.

T-head
with square neck                                                                                                  2.11.

Round
head                                                                                                                      2.12.

Mushroom
head                                                                                                               2.13.

Round
head with nib                                                                                                        2.14.

Mushroom
head with square neck                                                                                    2.15.

Round
head with oval neck                                                                                              2.16.

Cheese
head                                                                                                                     2.17.

Raised
cheese head                                                                                                         2.18.

Binding
head                                                                                                                    2.19.

Pan
head                                                                                                                          2.20.

Countersunk
head                                                                                                             2.21.

Undercut
countersunk head                                                                                              2.22.

Countersunk
head with nib                                                                                               2.23.

Countersunk
head with square neck                                                                                 2.24.

Raised
countersunk heart                                                                                                 2.25.

Undercut
raised countersunk head                                                                                   2.26.

Straight
knurled head                                                                                                       2.27.

Diamond
knurled head                                                                                                     2.28.

Normal
shank                                                                                                                   3.1.

Reduced
shank                                                                                                                 3.2.

Increased
shank                                                                                                               3.3.

Waisted
shank                                                                                                                  3.4.

Shoulder                                                                                                                          3.5.

Tubular
shank                                                                                                                  3.6.

Semi-tubular
shank                                                                                                          3.7.

As-rolled
end                                                                                                                  4.1.

Rounded
end                                                                                                                    4.2.

Chamfered
end                                                                                                                 4.3.

Cone
point                                                                                                                       4.4.

Truncated
cone point                                                                                                       4.5.

Cup
point                                                                                                                         4.6.

Flat
point                                                                                                                         4.7.

Long
dog point                                                                                                                 4.8.

Short
dog point                                                                                                                4.9.

Short
dog point with rounded end                                                                                    4.10.

Short
dog point with truncated cone end                                                                          4.11.

Scrape
point                                                                                                                    4.12.

4.14.
End for self-tapping screw                                                                                     4.13.

End
for thread rolling screw                                                                                            4.15.

Gimlet                                                                                                                              4.16.

Hexagon                                                                                                                           5.1.

Square                                                                                                                             5.2.

Triangle                                                                                                                           5.3.

Octagon                                                                                                                           5.4.

12point                                                                                                                            5.5.

Triangle                                                                                                                           5.6.

Square
socket                                                                                                                  5.7.

Hexagon
socket                                                                                                                5.8.

Six-spline
socket                                                                                                             5.9.

12point
socket                                                                                                                 5.10.

Slot                                                                                                                                  5.11.

Cross
recess                                                                                                                    5.12.

Wing                                                                                                                                5.13.

Straight
knurl                                                                                                                   5.14.

Diamond
knurl                                                                                                                 5.15.

Cross
hole                                                                                                                       5.16.

Hexagon
holt                                                                                                                    6.1.

Hexagon
fit bolt                                                                                                               6.2.

Hexagon
set screw with full dog point                                                                            6.3.

Hexagon
set screw with half dog point and flat cone point                                              6.4.

Hexagon
screw with waisted shank                                                                                 6.5.

Hexagon
bolt with collar                                                                                                 6.6.

Hexagon
bolt with flange                                                                                                 6.7.

Square
head bolt                                                                                                              7.1.

Square
head bolt with collar                                                                                           7.2.

Square
set screw with half dog point                                                                               7.3.

Square
set screw with cup point                                                                                      7.4.

Square
set screw with collar and half dog point with rounded end                                 7.5.

Triangle
head bolt with collar                                                                                         8.

Octagon
bolt                                                                                                                    9.

12point
flange screw                                                                                                       10.

T-head
bolt                                                                                                                      11.1.

T-head
bolt with square neck                                                                                          11.2.

T-head
bolt with double nib                                                                                            11.3.

Mushroom
head square neck bolt                                                                                    12.1.

Cup
head nib bolt                                                                                                            12.2.

Mushroom
head nib bolt                                                                                                  12.3.

Cup
oval neck bolt                                                                                                           12.4.

Flat
countersunk square neck bolt                                                                                    13.1.

Flat
countersunk nib bolt                                                                                                 13.2.

Deep
flat countersunk bolt                                                                                               13.3.

Hexagon
socket head cap screw                                                                                      14.1.

Hexagon
socket head shoulder screw                                                                              14.2.

Hexagon
socket countersunk cap head screw                                                                  14.3.

Slotted
cheese head screw                                                                                               15.1.

Slotted
pan head screw                                                                                                    15.2.

Slotted
raised cheese head screw                                                                                    15.3.

Slotted
raised cheese head screw with full dog point                                                      15.4.

Slotted
raised cheese head fit bolt                                                                                   15.5.

Slotted
capstan screw                                                                                                      15.6.

Slotted
small raised cheese head screw                                                                          15.7.

Slotted
countersunk head screw                                                                                       15.8.

Slotted
countersunk head screw with full dog point                                                        15.9.

Slotted
raised countersunk head screw                                                                                                                                             15.10.

Slotted
raised countersunk head screw with full dog point                                                                                                                                             15.11.

Countersunk
head screw with forgel slot                                                                                                                                             15.12.

Slotted
round head screw                                                                                                                                             15.13.

Cross
recessed raised cheese head screw                                                                       16.1.

Cross
recessed countersunk head screw                                                                          16.2.

Cross
recessed raised countersunk head screw                                                               16.3.

Cross
recessed pan head screw                                                                                       16.4.

Hexagon
screw with captive plain washer                                                                      17.1.

Hexagon
screw with captive spring and plain washer                                                     17.2.

Raised
cheese head screw with captive spring washer                                                   17.3.

Raised
countersunk head screw with captive countersunk serrated lock washer             17.4.

Eye
bolt                                                                                                                           18.1.

Mushroom
head anchor bolt                                                                                            18.2.

Flat
head anchor bolt                                                                                                       18.3.

Belting
bolt                                                                                                                      18.4.

Clip
bolt                                                                                                                          18.5.

Acorn
hexagon head bolt                                                                                                 18.6.

Conical
bolt                                                                                                                     18.7.

Masonry
bolt                                                                                                                   18.8.

Foundation
bolt                                                                                                                18.9.

Wing
screw                                                                                                                                             18.10.

Lifting
eye bolt                                                                                                                                             18.11.

Slotted
set screw with flat point                                                                                      19.1.

Slotted
set screw with full dog point                                                                               19.2.

Slotted
set screw with cup point                                                                                      19.3.

Slotted
set screw with cone point                                                                                    19.4.

Hexagon
socket set screw with flat point                                                                        19.5.

Hexagon
socket set screw with full dog point                                                                 19.6.

Hexagon
socket screw with cup point                                                                             19.7.

Hexagon
socket set screw with cone point                                                                      19.8.

Hexagon
head tapping screw                                                                                           20.1.

Slotted
pan head tapping screw                                                                                       20.2.

Slotted
countersunk head tapping screw                                                                          20.3.

Slotted
raised countersunk head tapping screw                                                               20.4.

Cross
recessed countersunk head tapping screw                                                             20.5.

Cross
recessed raised countersunk head tapping screw                                                  20.6.

Cross
recessed pan head tapping screw                                                                          20.7.

Hexagon
head wood screw                                                                                              21.1.

Square
head wood screw                                                                                                21.2.

Slotted
round head wood screw                                                                                      21.3.

Slotted
raised countersunk head wood screw                                                                  21.4.

Slotted
countersunk head wood screw                                                                             21.5.

Cross
recessed pan head wood screw                                                                             21.6.

Cross
recessed raised countersunk head wood screw                                                     21.7.

Cross
recessed countersunk head wood screw                                                                21.8.

Hexagon
head thread cutting screw                                                                                 22.1.

Slotted
cheese head thread cutting screw                                                                        22.2.

Slotted
countersunk head thread cutting screw                                                                22.3.

Slotted
raised countersunk head thread cutting screw                                                      22.4.

Cross
recessed pan head thread cutting screw                                                                 22.5.

Cross
recessed countersunk head thread cutting screw                                                    22.6.

Cross
recessed raised countersunk head thread cutting screw                                         22.7.

Hexagon
head thread forming screw                                                                                23.

Straight
knurled head screw                                                                                            24.1.

Straight
knurled head screw with cone point                                                                   24.2.

Straight
knurled head screw with short dog point with truncated cone end                     24.3.

Straight
knurled head screw with cup point                                                                     24.4.

Straight
knurled head screw with rounded point                                                              24.5.

Straight
knurled head screw with full dog point                                                              24.6.

Cylindrical
pin                                                                                                                25.1.

Cylindrical
pin with internal thread                                                                                 25.2.

Cylindrical
pin with cup points                                                                                       25.3.

Cylindrical
notched pin                                                                                                   25.4.

Cylindrical
notched pin with conical notches                                                                  25.5.

Tension
taper pin                                                                                                             25.6.

Taper
pin                                                                                                                         25.7.

Taper
pin with internal thread                                                                                         25.8.

Taper
pin with threaded stem                                                                                          25.9.

Spring
type straight pin                                                                                                                                             25.10.

Slotted
headless screw with flat chamfered end                                                                                                                                             25.11.

Hexagon
socket headless screw with flat chamfered end                                                                                                                                             25.12.

Hexagon
socket headless screw with truncated cone point                                                                                                                                             25.13.

Hexagon
socket headless screw with full dog point                                                                                                                                             25.14.

Hexagon
socket headless screw with cup point                                                                                                                                             25.15.

Stud                                                                                                                                 26.1.

Waisted
stud                                                                                                                    26.2.

Stud
bolt                                                                                                                          26.3.

Weld
stud                                                                                                                        26.4.

Double
end stud with full shank                                                                                       26.5.

Round
head rivet                                                                                                             27.1.

Mushroom
head rivet                                                                                                       27.2.

Countersunk
head rivet                                                                                                    27.3.

Raised
countersunk head rivet                                                                                         27.4.

Shallow
raised countersunk head rivet                                                                            27.5.

Flat
head rivet                                                                                                                 27.6.

Round
head hollow rivet                                                                                                 27.7.

Flat
head hollow rivet                                                                                                     27.8.

Countersunk
head hollow rivet                                                                                        27.9.

Flat
head semi-hollow rivet                                                                                                                                             27.10.

Countersunk
head semi-hollow rivet                                                                                                                                             27.11.

Round
head semi-hollow rivet                                                                                                                                             27.12.

Hexagon
nut                                                                                                                     28.1.

Hexagon
thin nut                                                                                                              28.2.

Hexagon
nut with collar                                                                                                   28.3.

Hexagon
nut with flange                                                                                                  28.4.

Washer
faced hexagon nut                                                                                               28.5.

Hexagon
weld nut                                                                                                            28.6.

Square
nut                                                                                                                        28.7.

Square
thin nut without chamfer                                                                                       28.8.

Foundation
nut                                                                                                                 28.9.

Square
nut with collar                                                                                                                                             28.10.

Square
weld nut                                                                                                                                             28.11.

Triangle
nut with collar                                                                                                                                             28.12.

Octagon
nut                                                                                                                                             28.13.

12point
flange nut                                                                                                                                             28.14.

Prevailing
torque type hexagon nut with deformed thread                                                                                                                                             28.15.

Prevailing
torque type hexagon nut with ring polymer insert                                                                                                                                             28.16.

Hexagon
slotted nut                                                                                                                                             28.17.

Hexagon
castle nut                                                                                                                                             28.18.

Hexagon
thin castle nut                                                                                                                                             28.19.

Acorn
nut                                                                                                                                             28.20.

Knurled
nut                                                                                                                                             28.21.

Slotted
round nut                                                                                                                                             28.22.

Slotted
round nut for hook-spanner                                                                                                                                             28.23.

Round
nut with set pin holes in side                                                                                                                                             28.24.

Round
nut with drilled holes in one face                                                                                                                                             28.25.

Wing
nut                                                                                                                                             28.26.

Plain
washer                                                                                                                    29.1.

Square
washer with round hole                                                                                       29.2.

Round
washer with square hole                                                                                       29.3.

Square
taper washer                                                                                                        29.4.

Single
coil spring lock washer with square ends                                                             29.5.

Single
coil spring lock washer with tang ends                                                                 29.6.

Double
coil spring lock washer                                                                                       29.7.

Curvet
spring washer                                                                                                       29.8.

Serrated
lock washer external teeth                                                                                 29.9.

Serrated
lock washer internal teeth                                                                                                                                             29.10.

Countersunk
serrated external toothed lock washer                                                                                                                                             29.11.

Wave
spring washer                                                                                                                                             29.12.

Lock
washer external teeth                                                                                                                                             29.13.

Lock
washer internal teeth                                                                                                                                             29.14.

Countersunk
external toothed lock washer                                                                                                                                             29.15.

Tab
washer with long tab and wing                                                                                                                                             29.16.

External
tab washer                                                                                                                                             29.17.

Tab
washer with long tab                                                                                                                                             29.18.

Internal
tab washer                                                                                                                                             29.19.

Split pin                                                                                                                           30.

V. УКАЗАТЕЛЬ ТЕРМИНОВ И НАИМЕНОВАНИЙ КРЕПЕЖНЫХ ИЗДЕЛИЙ НА ФРАНЦУЗСКОМ ЯЗЫКЕ

Filetage
cylindrique                                                                                                         1.1.

Filetage
conique                                                                                                              1.2.

Filetage
de vis à tôle                                                                                                       1.3.

Filetage
de vis à bois                                                                                                      1.4.

Filetage
métrique (SI)                                                                                                      1.5.

Filetage
métrique à pas fin                                                                                              1.6.

Tête
hexagonale                                                                                                               2.1.

Tête
hexagonale à collerette                                                                                            2.2.

Tête
hexagonale à embase cylindrique                                                                            2.3.

Tête
hexagonale à embase cylindro-tronconique                                                             2.4.

Tête
carrée                                                                                                                      2.5.

Tête
carrée à embase cylindrique                                                                                    2.6.

Tête
triangulaire à embase cylindrique                                                                            2.7.

Tête octogonale                                                                                                               2.8.

Tête
binexagonale                                                                                                            2.9.

Tête
rectangulaire à angles abattus                                                                                  2.10.

Tête
rectangulaire à angles abattus à
collet carré                                                            2.11.

Tête
ronde                                                                                                                       2.12.

Tête
bombée                                                                                                                    2.13.

Tête
ronde à ergot                                                                                                            2.14.

Tête
bombée à collet carré                                                                                              2.15.

Tête
ronde a collet carré large                                                                                        2.16.

Tête
cylindrique                                                                                                              2.17.

2.19.
Tête cylindrique bombée                                                                                        2.18.

Tête
cylindrique à dépouille                                                                                            2.20.

Tête
fraisée                                                                                                                      2.21.

Tête
fraisée à épaulement                                                                                                2.22.

Tête
fraisée à ergot                                                                                                          2.23.

Tête
fraisée à collet carré                                                                                                2.24.

Tête
fraisée bombée                                                                                                        2.25.

Tête
fraisée bombée à
épaulement                                                                                   2.26.

Tête
cylindrique moletée                                                                                                 2.27.

Tête
moletée croisé                                                                                                         2.28.

Tige
normale                                                                                                                   3.1.

Tige
réduite                                                                                                                     3.2.

Tige
ajustable                                                                                                                  3.3.

Tige
allégeé                                                                                                                     3.4.

Tige
ajustable à bout fileté réduit                                                                                    3.5.

Tige
tubulaire                                                                                                                  3.6.

Tige
demi-tubulaire                                                                                                         3.7.

Bout
plat                                                                                                                          4.1.

Bout
bombé                                                                                                                     4.2.

Bout
chanfreiné                                                                                                                4.3.

Bout
pointu                                                                                                                      4.4.

Bout
pilote                                                                                                                       4.5.

Cuvette                                                                                                                            4.6.

Bout
chanfreiné                                                                                                                4.7.

Téton
long                                                                                                                        4.8.

Тéton court                                                                                                                      4.9.

Téton
court bombé                                                                                                           4.10.

Téton
tronconique                                                                                                            4.11.

Bout
tronconique de vis à tôle                                                                                         4.12.

Bout
pointu de vis à tôle                                                                                                  4.13.

Bout
plat de vis à tôle                                                                                                      4.14.

Bout
de vis auto-taraudeuse par déformation de matière                                                 4.15.

Foret                                                                                                                                4.16.

Hexagonal                                                                                                                        5.1.

Carré                                                                                                                               5.2.

Triangulaire                                                                                                                     5.3.

Oclogonal                                                                                                                        5.4.

Bihexagonal                                                                                                                     5.5.

Triangle
creux                                                                                                                 5.6.

Carré
creux                                                                                                                      5.7.

Six
pans creux                                                                                                                 5.8.

Empreinte
six cannelures                                                                                                 5.9.

Empreinte
bihexagonale                                                                                                  5.10.

Fente                                                                                                                                5.11.

Empreinte
cruciforme                                                                                                      5.12.

Oreilles                                                                                                                           5.13.

Moleté                                                                                                                             5.14.

Moleté
croisé                                                                                                                  5.15.

Percage
en croix                                                                                                              5.16.

Vis à
tête hexagonale                                                                                                       6.1.

Corps
de boulon ajustable à tête hexagonale avec gorge de
dégagement                         6.2.

Vis à
tête hexagonale à téton
avec gorge de digagement                                                  6.3.

Vis à
tête hexagonale, à téton
cylindro-tronconique                                                        6.4.

Vis à tete
hexagonale à tige allégée                                                                                 6.5.

Vis à
tête hexagonale à embase
cylindrique                                                                    6.6.

Vis à
tête hexagonale à embase
cylindlro-tronconique                                                    6.7.

Vis à
tête carrée                                                                                                               7.1.

Vis à
tête carrée à embase
cylindrique                                                                            7.2.

Vis à
tête carrée à teton court                                                                                          7.3.

Vis à
tête carrée à cuvette                                                                                                7.4.

Vis à
tête carrée à embase
cylindrique à teton count                                                       7.5.

Vis à
tête triangulaire à embase
cylindrique                                                                    8.

Vis à
tête octogonale                                                                                                       9.

Vis à
tête bihexagonal                                                                                                      10.

Vis à
tête rectangulaire à angles abattus                                                                          11.1.

Vis à
tête rectangulaire à angles abattus à
collet carré                                                    11.2.

Vis à
tête rectangulaire à angles abattus à deux
ergots                                                    11.3.

Corps
de boulon à tête bombée aplatie, à
collet carré                                                     12.1.

Corps
de boulon à tête ronde, à ergot                                                                              12.2.

Corps
de boulon à tête bombee, à ergot                                                                           12.3.

Corps
de boulon à tête rondo, à
collet carré large                                                           12.4.

Corps
de boulon à tête fraisée, à
collet carré                                                                  13.1.

Corps
de boulon à tête fraisee, à ergot                                                                            13.2.

Corps
de boulon de roue                                                                                                 13.3.

Vis à
tête cylindrique a six pans creux                                                                            14.1.

Vis
ajustable à tête cylindrique a six pans creux
et à bout fileté réduite                          14.2.

Vis à
tête fraisée à six pans creux                                                                                    14.3.

Vis à
tête cylindrique fendue                                                                                           15.1.

Vis à
tête cylindrique à depouille fendue                                                                        15.2.

Vis à
tête cylindrique bombée large fendue                                                                     15.3.

Vis à
tête cylindrique bombée mince fendue, à
téton                                                       15.4.

Vis à
tête cylindrique bombée mince fendue, à tige
ajustable                                          15.5.

Vis à
tête cylindrique bombée fendue avec percage en croix                                          15.6.

Vis à
tête cylindrique bombée réduite fendue                                                                  15.7.

Vis à
tête fraisée fendue                                                                                                  15.8.

Vis à
tête fraisée fendue, à téton                                                                                      15.9.

Vis à
tête fraisée bombée fendue                                                                                                                                             15.10.

Vis à
tête fraisée bombée fendue, à
téton                                                                                                                                             15.11.

Vis à
tête fraisée à empreinte
rectangulaife ou à fente forgée                                                                                                                                             15.12.

Vis à
tête ronde fendue                                                                                                                                             15.13.

Vis à
tête cylindrique bombée à empreinte
cruciforme                                                    16.1.

Vis à
tête fraisée à empreinte
cruciforme                                                                        16.2.

Vis à
tête fraisée bombée à
empreinte cruciforme                                                           16.3.

Vis à
tête cylindrique à dépouille
à empreinte cruciforme                                              16.4.

Vis à
tête hexagonale à rondelle
cylindrique plate incorporée                                        17.1.

Vis à
tête hexagonale à rondelles
(élastique et cylindrique plate) incorporées               17.2.

Vis à
tête cylindrique bombée, à rondelle
élastique incorporée                                      17.3.

Vis
à tête fraisée bombée fendue,
à rondelee à dents extérieures, concave, incorporée  17.4.

Corps
de boulon à oeil                                                                                                    18.1.

Corps
de boulon à tête bombée à agrafe (1 ou 2)                                                            18.2.

Corps
de boulon à tête plate à agrafe (1 ou 2)                                                                 18.3.

Corps
de boulon de courroie                                                                                           18.4.

Crampon
fileté                                                                                                                 18.5.

Vis
à tête hexagonale à calotte                                                                                         18.6.

Vis
conique                                                                                                                      18.7.

Tige
de scellement à queue de carpe                                                                               18.8.

Tige
de scellement                                                                                                           18.9.

Vis
à oreilles                                                                                                                                             18.10.

Vis
à anneau                                                                                                                                             18.11.

Vis
sans tête, fendue, entiérement filetée, à bout
chanfreiné                                            19.1.

Vis
sans tête, fendue, entiérement filetée, à
téton                                                             19.2.

Vis
sans tête, fendue, entiérement filetée, à
cuvette                                                         19.3.

Vis
sans tête, fendue, entiérement filetée, à bout
pointu                                                   19.4.

Vis
sans tête, à six pans creux, entierement filetée,
à bout chanfreiné                             19.5.

Vis
sans tête, à six pans creux, entierement filetée,
à téton                                              19.6.

Vis
sans tête, à six pans crciix, entierement filelée,
à cuvette                                         19.7.

Vis
sans tête, à six pans creux, entierement filutée,
à bout pointu                                    19.8.

Vis à
tôle à tête hexagonale,
à bout pointu; à bout plat                                                    20.1.

Vis
à tôle à tête cylindrique
à depouille fendue, à bout pointu; à bout plat                      20.2.

Vis
à tôle à tête fraisée
fendue, à bout pointu; à bout plat                                                20.3.

Vis
à tôle à tête fraisée
bombée fendue, à bout pointu; à bout plat                                  20.4.

Vis
à tôle à tête fraisée
à empreinte cruciforme, à bout pointu; à bout plat                     20.5.

Vis
à tôle à tête fraisée
bombée à empreinte cruciforme, à bout pointu; à
bout plat        20.6.

Vis
à tôle à tête cylindrique
à depouille à empreinte cruciforme, à bout pointu;
à bout plat                                                                                                                                             20.7.

Vis
à bois à tête hexagonale                                                                                            21.1.

Vis
à bois à tête carrée                                                                                                    21.2.

Vis
à bois à tête ronde fendue                                                                                          21.3.

Vis
à bois à tête fraisée
bombée fendue                                                                          21.4.

Vis
à bois à tête fraisée
fendue                                                                                        21.5.

Vis
à bois à tête ronde à
empreinte cruciforme                                                               21.6.

Vis
à bois à tête fraisée
bombée à empreinte cruciforme                                                21.7.

Vis
à bois à tête fraisée
à empreinte cruciforme                                                              21.8.

Vis
auto-taraudeuse à tête hexagonale                                                                             22.1.

Vis
auto-taraudeuse à tête cylindrique
fendue                                                                 22.2.

Vis
auto-taraudeuse à tête
fraisfée fendue                                                                       22.3.

Vis
auto-taraudeuse à tête fraisée
bombée fendue                                                           22.4.

Vis
auto-taraudeuse à tête cylindrique
à dépouille à empreinte cruciforme                    22.5.

Vis
auto-taraudeuse à tête fraisée
à empreinte cruciforme                                              22.6.

Vis
auto-taraudeuse à tête fraisée
bombée à empreinte cruciforme                                 22.7.

Vis
auto-taraudeus par deformation de matiére                                                               23.

Vis
à tête cylindrique moletée                                                                                         24.1.

Vis
à tête cylindrique moletée, à
bout pointu                                                                   24.2.

Vis
à tête cylindrique moletée à
téton cylindro-tronconique                                            24.3.

Vis
à tête cylindrique moletée à
cuvette                                                                          24.4.

Vis
à tête cylindrique moletée à
bout bombée                                                                 24.5.

Vis
à tête cylindrique moletée à
téton long                                                                      24.6.

Goupille
cylindrique                                                                                                       25.1.

Goupille
cylindrique à filet femelle                                                                                25.2.

Goupille
cylindrique à cuvette                                                                                        25.3.

Goupille
cylindrique à taille                                                                                           25.4.

Goupille
cylindrique à tailles coniques                                                                           25.5.

Goupille
conique fendue                                                                                                  25.6.

Goupille
cunique                                                                                                             25.7.

Goupille
conique à filet femelle                                                                                      25.8.

Goupille
conique à tourillon fileté                                                                                  25.9.

Goupille
elastique                                                                                                                                             25.10.

Vis
sans tête fendue, partiellement filetée, à bout
chanfreiné                                                                                                                                             25.11.

Vis
sans tête à six pans creux, partiellement, filetée,
à bout chanfreiné                                                                                                                                             25.12.

Vis
sans tête à six pans creux, partiellement filetée, à
bout pointu                                                                                                                                             25.13.

Vis
sans tête à six pans creux, partiellement filetée, à
téton                                                                                                                                             25.14.

Vis
sans tête à six pans creux, partiellement filetée, à
cuvette                                                                                                                                             25.15.

Goujon                                                                                                                             26.1.

Goujon
à corps allégé                                                                                                      26.2.

Tige
filetée                                                                                                                      26.3.

Tige
à sounde                                                                                                                  26.4.

Goujon
à deux gorges de dégagement et à téton                                                               26.5.

Rivet
à tête ronde                                                                                                            27.1.

Rivet
à tête bombée                                                                                                         27.2.

Rivet
à tête fraisée                                                                                                           27.3.

Rivet
à tête fraisée bombée                                                                                             27.4.

Rivet
à tête fraisée bombée bas                                                                                       27.5.

Rivet
à tête plate                                                                                                              27.6.

Rivet
cretix à tête ronde                                                                                                  27.7.

Rivet
creux à tête plate                                                                                                    27.8.

Rivet
creux à tête fraisée                                                                                                 27.9.

Rivet
semi-creux à tête plate                                                                                                                                             27.10.

Rivet
semi-crcux à tête fraisée                                                                                                                                             27.11.

Rivet
semi-creux à tête ronde                                                                                                                                             27.12.

Ecrou
hexagonal                                                                                                              28.1.

Ecrou
hexagonal bas                                                                                                        28.2.

Ecrou
hexagonal à embase cylindrique                                                                            28.3.

Ecrou
hexagonal à embase cylindro-tronconique                                                            28.4.

Ecrou
hexagonal à collerette                                                                                           28.5.

Ecrou
hexagonal à souder                                                                                                28.6.

Ecrou
carré                                                                                                                      28.7.

Ecrou
carre bas                                                                                                               28.8.

Ecrou
de tige d’ancrage                                                                                                   28.9.

Ecrou
carré à embase cylindrique                                                                                                                                             28.10.

Ecrou carré
à souder                                                                                                                                             28.11.

Ecrou
triangulaire à embase cylindrique                                                                                                                                             28.12.

Ecrou
octogonal                                                                                                                                             28.13.

Ecrou
bihexagonal                                                                                                                                             28.14.

Ecrou
auto-freiné hexagonal à filet déformé                                                                                                                                             28.15.

Ecrou
auto-freiné hexagonal anneau polimére                                                                                                                                             28.16.

Ecrou
hexagonal à créneaux                                                                                                                                             28.17.

Ecrou
hexagonal à créneaux dégagés                                                                                                                                             28.18.

Ecrou
hexagonal bas à creneaux dégagés                                                                                                                                             28.19.

Ecrou
borgne à calotte                                                                                                                                             28.20.

Ecrou
moleté                                                                                                                                             28.21.

28.23.
Ecrou cylindrique à fente                                                                                                                                             28.22.

Ecrou
cylindrique à trous percés en croix                                                                                                                                             28.24.

Ecrou
cylindrique à deux trous percés sur une fase                                                                                                                                             28.25.

Ecrou
à oreilles                                                                                                                                             28.26.

Rondelle
plats                                                                                                                 29.1.

Plaquette
carrée                                                                                                               29.2.

Rondelle
plate à trou carrée                                                                                            29.3.

Plaquette
oblique                                                                                                             29.4.

Rondelle
élastique simple spire sans becs                                                                      29.5.

Rondelle
élastique simple spire abes becs                                                                      29.6.

Rondelle
élastique double spire sans becs                                                                      29.7.

Rondelle
élastique cintrée                                                                                               29.8.

Rondelle
élastique plane à dents chevauchantes extérieures                                           29.9.

Rondelle
élastique plane à dents chevauchantes intérieures                                                                                                                                             29.10.

Rondelle
élastique concave à dents chevauchantes extérieures                                                                                                                                             29.11.

Rondelle
élastique ondulée                                                                                                                                             29.12.

Rondelle
élastique plane à dents espacées extérieures                                                                                                                                             29.13.

Rondelle
élastique plane à dents espacées intérieures                                                                                                                                             29.14.

Rondelle
élasllque concave à dents espacées extérieures                                                                                                                                             29.15.

Frein
d’ecrou d’equerre à aileron                                                                                                                                             29.16.

Rondelle
frein d’ecrou à ergot extérieur                                                                                                                                             29.17.

Frein
d’ecrou droit à aileron                                                                                                                                             29.18.

Rondelle
frein d’ecrou à ergot intérieur                                                                                                                                             29.19.

Goupille
cylirndrique fendue                                                                                           30.

ИНФОРМАЦИОННЫЕ
ДАННЫЕ

1. РАЗРАБОТАН И
ВНЕСЕН Министерством черной металлургии СССР

РАЗРАБОТЧИКИ

Б.М. Ригмант; Т.Е. Юрченко

2.
УТВЕРЖДЕН И ВВЕДЕН В ДЕЙСТВИЕ Постановлением Государственного комитета СССР по
стандартам от 30.09.86 № 2941

3. Срок проверки
2000 г., периодичность проверки — 10 лет

4. Стандарт
полностью соответствует стандарту СТ СЭВ 6300-88

5. Стандарт
полностью соответствует международному стандарту ИСО 1891-79

6. ВВЕДЕН
ВПЕРВЫЕ

7. ССЫЛОЧНЫЕ НОРМАТИВНО-ТЕХНИЧЕСКИЕ ДОКУМЕНТЫ

Обозначение НТД, на который дана ссылка

Номер пункта

ГОСТ 11708-82

Вводная часть

8. ПЕРЕИЗДАНИЕ март 1990 г. с Изменением № 1, утвержденным в июне
1989 (ИУС 11-89)

СОДЕРЖАНИЕ

Алфавитный
указатель терминов на русском языке. 4

Алфавитный указатель терминов на немецком языке. 5

Алфавитный указатель терминов на английском языке. 5

Алфавитный указатель терминов на французском языке. 6

Приложение Терминология
и номенклатура крепежных изделий на русском, немецком, английском и
французском языках. 6

I. Терминология и номенклатура крепежных
изделий. 6

1. Резьба. 6

2. Формы головок. 7

3. Формы стержней. 9

4. Концы болтов и винтов. 10

5. Элементы, передающие вращение. 11

6. Болты и винты с шестигранной головкой. 12

7. Винты с четырехгранной (квадратной) головкой. 13

8. Болты с трехгранной головкой. 13

9. Болты с восьмигранной головкой. 13

10. Болты с двенадцатигранной головкой. 13

11. Болты с т-образной головкой. 13

12. Болты с полукруглой головкой. 14

13. Болты с потайными головками. 14

14. Винты с внутренним шестигранником.. 14

15. Винты с прямым шлицем.. 14

16. Винты с крестообразным шлицем.. 15

17. Винты с невыпадающими деталями. 15

18. Различные типы болтов и винтов. 16

19. Установочные винты без головок. 17

20. Самонарезающие винты.. 17

21. Шурупы.. 17

22. Резьбонарезающие винты.. 18

23. Резьбовыдавливающие винты.. 18

24. Винты с рифленой головкой. 18

25. Штифты.. 19

26. Шпильки. 20

27. Заклепки. 20

28. Гайки. 21

29. Шайбы.. 23

30. Шплинты.. 25

II. Алфавитный указатель терминов и
наименований крепежных изделий на русском языке. 25

III. Указатель терминов и наименований
крепежных изделий на немецком языке. 31

IV. Указатель терминов и наименований
крепежных изделий на английском языке. 36

V. Указатель терминов и наименований крепежных изделий
на французском языке. 42

 

Оцените статью
Комментарии читателей